GoMix K12 Flex Waterproofing Slurry
High Elasticity Two-Component Cementitious Waterproofing Mortar
Two-component (25kg powder + 12.5kg liquid) cementitious mortar with high elasticity
130% elongation & superior crack resistance (usable with fiberglass mesh for enhancement)
1.5bar impermeable, fully waterproof against ground moisture & hydrostatic pressure
Excellent chemical resistance (COβ, SOβ, chlorides, sulphates from seawater/ground)
Strong adhesion to cementitious, ceramic, marble & most solid substrates
Weather/frost/deicing agent resistant, suitable for coastal/industrial polluted areas
Water vapor permeable, easy application by brush/roller/spray (2mm dry film thickness)
130% Elongation
1.5bar Impermeable
Applications for GoMix K12 Flex Waterproofing Slurry
Ideal for complex surfaces requiring high elasticity and chemical resistance
Swimming pools, fountains & water tanks
(potable/non-potable)
Tunnels, culverts & retaining walls
waterproofing
Terraces, balconies & patios
(interior/exterior)
Bathrooms, kitchens & toilets
(pre-tiling waterproofing)
Basements, suspended floors
& precast floor slabs
Concrete, brickwork, blockwork
& cementitious rendering waterproofing
Crack sealing & protective coating
for concrete/masonry surfaces
Ideal for complex surfaces, coastal/industrial areas; not for gypsum boards or incomplete wrapping scenarios
Technical Specifications - GoMix K12 Flex Waterproofing Slurry
All data tested under standard conditions. For project-specific dosage advice, contact our technical team.
Application & Mixing Guidelines
Surface Preparation
All substrates: clean, dry, free of oil/grease/dust/foreign matter; structurally solid
Painted surfaces: abrade to expose 80% original substrate; building boards: flat & firmly fixed
Cement-based plasters: cure for 14 days; cracks/level deviations repaired
Pre-wet substrate to saturation (no free water, matt surface)
Mixing Steps
Pour 12.5kg Component B (liquid) into clean vessel β add 25kg Component A (powder)
Mix with 350 rpm low-speed mechanical mixer until lump-free homogeneous slurry
Avoid high-speed mixing (prevents air bubbles that weaken waterproofing)
Application Operation
1st coat: apply with brush/roller/sprayer (even coverage)
2nd coat: apply 4-5hrs later at 90Β° angle to 1st coat (while 1st is still green)
Total thickness β€5mm; tile application starts after β₯12hrs curing
Water tanks/pools: cure β₯7 days before filling water; wrap internal surfaces completely
Corners: use net to prevent damage; pipes: add insulation for water discharge
Key Warnings
Do not add cement/sand to the mixture; do not use on gypsum boards
Do not apply below 5Β°C; protect from water/rain for 24hrs post-application
Incomplete wrapping causes leakage (critical for pools/tanks); not for non-solid substrates
Why Choose GoMix K12 Flex Waterproofing Slurry?
Ultra High Elasticity
130% elongation, superior crack resistance, adapts to substrate movement
Strong Impermeability
1.5bar waterproof pressure, blocks ground moisture & hydrostatic pressure
Super Chemical Resistance
Withstands seawater/industrial pollutants (chlorides, sulphates, COβ)
Universal Adhesion
Bonds firmly to cementitious/ceramic/marble substrates, no peeling
All-Weather Durability
Frost/deicing agent resistant, suitable for coastal/harsh environments
Complex Surface Adaptability
Better integrity on complicated surfaces than membrane-type waterproofing
High Elastic Two-Component Formula
1.5bar Impermeable & Chemical Resistant
130% Elongation & Crack Resistant
1 Year Long Shelf Life
Non-Toxic & Water Vapor Permeable
Global Technical Support
GoMix specializes in high-flex waterproofing slurries, with strict quality control and rich large-project (tunnels/pools) construction experience.